WIFI Router IEEE802.11n 2x2

Introduction
Datasheet Download
1. Product Overview
 

1-1. Introduction

The 802.11n wireless router provides a better wireless signal for your network than previous-generation 802.11g technology. Upgrading your home network to 802.11n wireless router provides an excellent solution for sharing an Internet resource and files such as video, music, and documents. Use intelligent antenna technology to transmit multiple streams of data which enables you to receive wireless signals faster at your home. Not only the 802.11n technology extends your wireless range, it also works with previous-generation 802.11b/g wireless devices. The wireless router also includes QoS (Quality of Service) prioritization technology that analyzes and separates multiple data streams based on sensitivity to delay, enabling multiple applications to stream smoothly across your network. Supports wireless 802.11b/g/n and the following security protocols: WEP, WPA, WPA2.
The wireless router has Quick Setup Wizard quickly configures your new wireless router to get you up and running in minutes. Our Setup Wizard shows you step by step through the installation process to configure your Internet connection, wireless network settings and security.
 

1-2. Specifications

 
Wireless Features
 
  • Complies with IEEE 802.11b/g/n standards
  • Backward compatible with 802.11b/g devices while operating at 802.11n data rate
  • 2x2 MIMO technology for extended reception robustness and exceptional throughput
  • 802.11b/g Data rates : 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54Mbps, 802.11n maximum Data rates :150Mbps receive/transmit PHY rate using 40MHz bandwidth, 300Mbps receive/transmit PHY rate using 40MHz bandwidth
  • Burst-mode support for dramatically enhanced throughput
  • DSSS with DBPSK and DQPSK, CCK modulations and demodulations supported with rate compatible punctured convolutional coding with coding rate of 1/2, 2/3, 3/4 and 5/6
  • OFDM with BPSK, QPSK, 16QAM and 64QAM modulations and demodulations supported with long and short preamble
  • Complies with IEEE 802.11e QoS Enhancement (WMM)
  • IEEE 802.11i (WPA, WPA2). Open, shared key and pair-wise key authentication services
 

2. Hardware Architecture


2-1. Hardware Interfaces
  • Four RJ-45 ports for 10/100 Base-T Ethernet LAN connect to PC
  • One RJ-45 port for WAN access
  • One reset button to default setting
  • One WPS / WiFi on/off  button
  • One power jack
  • One power switch (option)
  • One/Two WIFI antenna
  • LED indicators


2-2. Block Diagram



2-3. LED Definitions

 
Mode Label Display Color Meaning
Power PWR

 
Light Power on,
Off Power off
WAN WAN Light Connection is OK
Blink Data transmitting or receiving
Off Connection is not established
LAN LAN

 
Light Ethernet line is connected
Off Ethernet line not connected
Blink Transforming data
WLAN WLAN Light Wireless device is ready
Off Wireless device is not ready
Blank Transforming data
WPS WPS Light Connection is OK
Off Disconnection
 

3. SOFTWARE FEATURE


WLAN AP
  • ON/OFF software switch
  • IEEE 802.11b, 11g,11n, and Mixed
  • WEP, WPA TKIP/AES and WPA2 TKIP/AES/Mixed
  • Wireless Auto-channel selection
  • Wireless repeater
  • MBSSID
  • STA power saving mode
  • SSID broadcast or not
  • MAC filter

QoS
  • Traffic shaping
  • WLAN QoS supported

Security  
  • URL Blocking
  • MAC Clone

NAT/NAPT

ALG: support H.323, SIP, RTSP, L2TP, IPSEC, FTP, PPTP, IQC, MSN,
              NetMeeting, CUSEEME, IRC, SNMP

DMZ

DHCP server

DNS
  • Relay
  • Client
  •  server

UPnP

WAN connection type
  • Static IP
  • PPPoE
  • DHCP

Management
  • Remote management
  • Configuration backup/restore
  • Firmware upgrade
  • Access control

DDNS
  • DynDns
  • TZO
  • dlinkddns
  • Oray
 

4. Operation Specifications


4-1. Electrical


4-1-1. Power Requirements

 

This Device uses an AV adaptor.
AC power adaptor: 220 VAC, 50/60Hz (can be customized)
Output voltage:5VDC, 1.0A

4-1-2. Heat & Power

Dissipation Power: < 5W

4-2. Electromagnetic Conpatibility 

Complies with the following standards:
  • Temperature:
- 0 to 40 degrees C (Standard Operating)
- -40 to 70 degree C (Non-operating)
  • Humidity:
- 10% to 90% (Non-condensing, Standard Operating)
  • Vibration: IEC 68-2-36, IEC 68-2-6
  • Shock: IEC 68-2-29
  • Drop: IEC 68-2-32

Design in Taiwan, Made in China